import { test } from '@playwright/test';
import { markManual } from '../../helpers/manual';

// Codec-level tests require active SIP calls with specific codec configurations
// and packet capture / audio analysis tools. None can be driven by Playwright alone.

test.describe('pbx-codecs', () => {
  test('pbx-codecs-check-codec_negotiation_g711_g729_opus_g722', async ({ page }, testInfo) => {
    testInfo.annotations.push({ type: 'automationStatus', description: 'manual' });
    testInfo.annotations.push({ type: 'testType', description: 'check' });
    markManual('Requires SIP call traffic with codec-constrained endpoints and Wireshark packet capture to verify SDP offer/answer negotiation for each codec');
    testInfo.annotations.push({ type: 'description', description: 'Verify successful codec negotiation for G.711 (alaw/ulaw), G.729, Opus, and G.722 between endpoints' });
    // Manual steps:
    // 1. In admin portal, configure a test extension to use only G.711 alaw. Make a call and capture SDP.
    //    Verify SDP answer contains only pcma/8000.
    // 2. Repeat with G.729: verify annexb, SDP shows g729/8000.
    // 3. Repeat with Opus: verify SDP shows opus/48000/2.
    // 4. Repeat with G.722: verify SDP shows G722/8000.
    // 5. Test codec fallback: configure preferred codec that remote doesn't support; verify negotiation falls back to next common codec.
    // 6. Record Wireshark SDP captures for each scenario.
  });

  test('pbx-codecs-check-dtmf_transmission_rfc2833_inband_sip_info', async ({ page }, testInfo) => {
    testInfo.annotations.push({ type: 'automationStatus', description: 'manual' });
    testInfo.annotations.push({ type: 'testType', description: 'check' });
    markManual('Requires active call sessions with DTMF generation (physical or software phone), packet capture for RFC2833, and IVR system to verify DTMF reception');
    testInfo.annotations.push({ type: 'description', description: 'Verify DTMF digit transmission via RFC2833, in-band audio, and SIP INFO methods are handled correctly' });
    // Manual steps:
    // 1. Configure extension for RFC2833 DTMF. Call an IVR. Press digits 0-9,*,#.
    //    Wireshark: verify RTP telephone-event packets are sent for each digit.
    //    IVR: verify digits are recognised and routing occurs correctly.
    // 2. Configure extension for in-band DTMF. Repeat dial-through IVR.
    //    Verify IVR recognises tones (confirm with IVR logs).
    // 3. Configure extension for SIP INFO DTMF. Repeat.
    //    Wireshark: verify SIP INFO messages contain correct DTMF signal field.
    // 4. Record: each method used, packets observed, IVR recognition accuracy.
  });

  test('pbx-codecs-check-t38_fax_passthrough_and_error_correction', async ({ page }, testInfo) => {
    testInfo.annotations.push({ type: 'automationStatus', description: 'manual' });
    testInfo.annotations.push({ type: 'testType', description: 'check' });
    markManual('Requires fax hardware (physical fax machine or fax server, e.g., HylaFAX) and T.38 stack support; cannot be tested with a browser');
    testInfo.annotations.push({ type: 'description', description: 'Verify T.38 fax passthrough and error correction (ECM) work correctly over the PBX' });
    // Manual steps:
    // 1. Configure a SIP trunk with T.38 support enabled.
    // 2. Send a fax from a fax machine / software fax client to a DID number routed to a fax extension.
    // 3. Verify the fax is received completely and without page corruption.
    // 4. Check Wireshark: verify T.38 re-INVITE is sent when fax tone is detected (CNG → T.38 switchover).
    // 5. Test T.38 ECM: induce packet loss (network emulator), verify re-transmission corrects errors.
    // 6. Record: pages sent/received, error count, ECM effectiveness.
  });
});
